3.Altimeter setting procedures
These procedures apply to all flights. Exceptions and conditions may be determined by appropriate ATS unit.
Procedures describe the method for providing adequate vertical separation between aircraft and for providing required terrain clearance during all phases of a flight. This method is based on the following provisions:
3.1.1Transition altitude (TA)
Transition altitude is the altitude at or below which the vertical position of an aircraft is controlled by reference to altitudes. The transition altitude within all FIR is 5000 ft (1500 m) AMSL, except as stated below.
Outside TMA in mountainous areas where terrain exceeds 4000 ft (1200 m) AMSL, the transition altitude for all VFR flights and for IFR flights outside ATS routes is increased to an altitude identical to the height 1000 ft (300 m) AGL.
3.1.2Transition level (TL)
Transition level is the lowest flight level available for use, located at least 1000 ft (300 m) above the transition altitude.
The airspace between the transition level and the transition altitude is called the transition layer. En-route horizontal flight is not permitted within the transition layer except especially approved activities (see AIP CR ENR 220.127.116.11). Minimum depth of transition layer is set to 1000 ft (300 m) in accordance with ICAO Doc. 7030/5.
3.2References to the vertical position
3.2.1The vertical position of aircraft shall be expressed in terms of:
- flight levels for flight at or above the transition level;
- altitudes for flight at or below transition altitude;
- heights above the ground for en-route flight up to 1000 ft (300 m) above the ground;
3.2.2While passing through the transition layer, vertical posotion shall be expressed in term of:
- flight levels when climbing; and
- altitude when descending.
3.3The change in reference from altitude to flight levels and vice versa
The change in reference from altitude to flight levels and vice versa is made:
- at the transition altitude when climbing; and
- at the transition level when descending.
3.4Description of altimeter setting region and procedures for pilots
3.4.1During flight at or below the transition altitude QNH shell be set as follows:
- QNH of the controlled aerodrome
- in CTR, TMA and ATZ whose upper limit or its part is identical with lower limit of TMA,
- below TMA, when flights are carried out between the lower limit of TMA, which is defined
by altitude (AMSL)*, and the altitude 1000 ft (300 m) below this limit.
Note: * Lower limit of TMA defined by altitude (AMSL) is always references to the QNH of the controlled aerodrome to which TMA belongs.
Note: It concerns flights in the area situated right below the lower limit of TMA, that may cause, by setting wrong pressure, unintened and undesirable disruption of the TMA.
- regional QNH or QNH of the nearest uncontrolled aerodrome
- in other cases.
Note: Regional QNH is a forecast of minimum value of QNH within FIR Praha for a specified time period.
- in other cases.
3.4.2Information on the aerodrome QNH, temperature and transition level in TMA is provided in ATIS broadcasts or transmitted by the appropriate ATS unit. Regional QNH is provided in MET broadcasts and is available on request from the ATS units.
3.4.3QNH values are given in hectopascals. QNH in milimetres Hg is provided on request. Minimum flight altitudes are published in appropriate charts.
3.4.4VFR flights up to an altitude of 5000 ft (1500 m) AMSL or up to a height 1000 ft (300 m) AGL, if this level exceeds 5000 ft (1500 m) AMSL, shall set the altimeter to the QNH in accordance with paragraph 3.4.1.
Levels at which a flight is to be conducted shall be specified in a flight plan:
- flight levels for flight at or above the lowest usable flight level or above transition altitude;
- altitudes for flight at transition altitude or below;
- abbreviation VFR for uncontrolled VFR flights.
3.6Procedures in controlled airspace
3.6.1If a VFR flight within controlled airspace is cleared by ATC to an altitude which the pilot finds unacceptable he/she shall request an alternative altitude. If such a request is not received ATC will consider that the clearance has been accepted and will be complied with.
Vertical separation from IFR flights is provided within controlled airspace Class C by assignment of different levels. ATC unit may clear VFR flight to level which is specified for IFR flight.
3.7Table of cruising levels
All en-route VFR flights shall be operated in VFR cruising levels corresponding to the flown track according to table of cruising levels stated below. However ATC unit providing service in controlled airspace may also assign level that is specified for IFR flights.
|Table of cruising levels|
|from 000° to 179°||from 180° to 359°|
3.8Transition levels according to the current QNH
|QNH in hPa||Transition level|